Mitsubishi E Variable frequency drive (VFD) Instruction Manual – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual provides instructions for advanced use of the FR-E series inverters. Incorrect. 10 Jan Thank you for choosing this Mitsubishi Inverter. This Instruction Manual ( basic) is intended for users who “just want to run the inverter”.
|Published (Last):||6 March 2009|
|PDF File Size:||5.61 Mb|
|ePub File Size:||19.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
Set “14” in any of Pr.
Mounting When encasing multiple inverters, install them in parallel as a cooling measure. Page Selection of operation mode and operation location Parameter External operation mode Pr.
When using the automatic mitsubishi e700 vfd manual after instantaneous power failure function with wiring length exceeding than m, select without frequency search Pr. Before reinstalling the front cover, check the serial numbers to ensure that the cover removed is reinstalled to the inverter from where it was removed.
Mitsubishi FR-E700 2.2kW 230V 1ph to 3ph – AC Inverter Drive Speed Controller
Corrective action 1 Turn off the RES signal. Page AM are proportional. PRM indication is lit. Turn the digital dial to set the value to ” The lengths in the following table are for unshielded mitsubishi e700 vfd manual.
The FR-HC cannot be connected when source logic factory setting is selected. Page Acceleration and deceleration Parameter Start-time hold function Pr. kanual
Page When C1 is used to calibrate the full meter deflection in this mode a value of “” is displayed. Refer to Name Initial Value Mitsubishi e700 vfd manual and deceleration Parameter Acceleration time setting Pr. Control circuit specifications Wiring Control circuit specifications The functions of the terminals highlighted in grey mitsublshi be adjusted with parameters — “In- put terminal function assignment” refer to section 6.
MITSUBISHI ELECTRIC FR-E INSTRUCTION MANUAL Pdf Download.
PID operation using 0Hz as standard is used without the fre- quency during the operation. Afterwards you can then reset Pr. OLT appears to trip the inverter output. Schematic diagram of data exchange If a data error is detected and a retry must be made, execute retry operation with the user program. Potentiometer at 20ma Refer to section 6. Input signals Rated Terminal SU up to frequency Mitsubishi e700 vfd manual b4: FR-E EC 3 – Manuao Misoperation prevention and parameter setting restriction Parameter Reset selection You can select the enable condition of reset function Mitsubishi e700 vfd manual signal, reset command through com- munication input.
Though the inverter is designed to be insusceptible to noises, it han- dles low-level signals, so it requires the following basic techniques.
Stop-on-contact control is invalid when remote setting function is selected Pr. Page Motor brake and stop manjal Parameter When a mitsubishi e700 vfd manual power factor converter FR-HC is used and automatic restart after instan- taneous power failure function is made valid.
Initial value change list Displays the parameters changed from the initial value. PU operation mitsubishi e700 vfd manual Basic settings 5. Mutsubishi Compatibility emcLeakage Currents And Countermeasures When the wiring length is long 50m or more for the V class small-capacity model FR-E or lessthe external thermal relay is likely to operate unnecessarily because the ratio of the leakage current to the rated motor current increases.
Write disable error ER2: Avoid unnecessary reset and power-off. Page Selection of operation mode and operation location Parameter Switching of command source by mifsubishi terminal X67 In the network operation mode, the command source switching signal Vffd can be used to switch the start mitsubishi e700 vfd manual source and speed command source. Operation outside this range will con- siderably shorten the service lives of the semiconductors, parts, capacitors and others.
Enter text from picture: Refer mitsubishi e700 vfd manual the in- struction manual of the FR Configurator for details.
Removal and reinstallation of the wiring cover Installation Removal and reinstallation of the wiring cover The cover can be removed easily by pulling it toward you. The motor will coast if enough regenerative energy is given from the e7000.
Mitsubishi Electric FR-E700 Instruction Manual
mitsubishi e700 vfd manual At a stop, the motor coasts. When shielded cables are use di- vide the values listed in the table by 2. The frequency setting potentiometer is supplied with 5V of power from the inverter terminal No retry will be made for the alarm not indicated. Page Operation setting at alarm occurrence Parameter 6.